![macroplant ibrowse macroplant ibrowse](https://www.macrobites.com/uploads/2/0/4/5/20452203/img-0888.jpg)
- MACROPLANT IBROWSE FOR FREE
- MACROPLANT IBROWSE HOW TO
- MACROPLANT IBROWSE ANDROID
- MACROPLANT IBROWSE SOFTWARE
IExplorer is more of an all-in-one app and offers a whole lot more features than iBrowse.
![macroplant ibrowse macroplant ibrowse](https://assets.macroplant.com/assets/ibrowse/screenshots/coverflow-c91a952e1c5f410ea9c1f0fbad93b00648c106f2cc36b1185baf2ebc456703e2.jpg)
MACROPLANT IBROWSE FOR FREE
The Kit that supports the power profiler feature are the PRO and the EXPERT kit, the basic kit doesn't have this functionallity.We recently discontinued iBrowse since you can still do ALL of the same things you did for free in iBrowse in iExplorer 3 for completely free too. Which dev kit support the power profile measurement via Smart Snippets? Undefine the EEPROM_ON and the CFG_MULTI_BOND features.Undefine the INACTIVITY_TIMEOUT_ON definition in the app_kbd_config.h file.Define the NORMALLY_CONNECTABLE definition in the app_kbd_config.h file.Remove the unconditional sleep command in the app_init_func(), just comment out the app_set_extended_sleep.Disable the sleep modes from the da14580_config.h file.There are a few thing to set in order for the keyboard reference design to be able to run on a basic kit: How can i run the keyboard reference design on a basic kit ? This functionallity is not supported by the iOS application. In the Smart Tag reference design there a functionallity where the user can trigger the phone in order to start alerting via pushing the button on the Smart Tag. In the Ios Smart Tag application, why i cant enable the find me locator service on my phone? J4 - VBAT_580 - > to the Vcc of the custom board.J4 - RST - > to the RST pin of the custom board.J4 - URX - > on the TX pin of the custom board.J4 - UTX - > on the RX pin of the custom board.UART interface, the required connections are: J4 - Pin 2 (GND) - > to the ground of the custom board.TP2 -> to the Vpp of the custom board (if OTP needs to be programmed).J4 - Pin 27 (TCK) - > SW_CLK pin of custom board.J4 - Pin 25 (TMS) - > SWDIO pin of custom board.J4 - Pin 1 (VBAT_580) - > Vcc of the custom board.JTAG interface, the required connections are: Below are the required connections for each interface. This can be done either via UART or the JTAG interface. You can program your custom design's by using the Dialog development kits that you allready have.
![macroplant ibrowse macroplant ibrowse](https://assets.macroplant.com/assets/ibrowse/screenshots/ibrowse-pc-backups-0a9c7c0df313053fb839f4d038778efddf3158ad7948abde20c74ce566e6a32e.png)
MACROPLANT IBROWSE HOW TO
How to program a custom board using a development kit (basic or pro)? Line 143: change spi_mem_cs_high() -> spi_cs_high()
![macroplant ibrowse macroplant ibrowse](https://assets.macroplant.com/assets/ibrowse/screenshots/ibrowse-root-access-d64e36872bddb986d175a8fdb3dd0ee737e598eeae90cada98b607bf384a131e.png)
Line 123: change spi_mem_cs_low() -> spi_csl_low() In the Secondary_bootloader project, port and or pin numbers for the UART, SPI or EEPROM can be changed in the file : periph_setup.hįor the SPI FLASH 2 settings have to be changed in the file: spi_commands.c: How to change peripheral port/pin settings in the secondary bootloader. In UM-B-034 (see our Support website) in APPENDIX Battery connection 'workaround' the problem is explained and the solution is visialized by using electrical schematic and photo. When USB is disconnected, then T_RESET becomes low.Īfter invertor U7 RST is high. When the board operates on battery (J11 jumper on 2-3), the RST-signal is permanently high. The root cause of this is in the DSPS device firmware and will be fixed for the next release.
MACROPLANT IBROWSE ANDROID
The issue will be fixed in the next revision of the Android applicationģ)When transmitting the value "0x00" from DSPS-device (PC terminal +DevKit) to android, The value 0x00 and following data will not be displayed if the total number of bytes is smaller than 8-byte. Workaround: Change the value to something else GPIO_ConfigurePin( GPIO_PORT_0, GPIO_PIN_5, INPUT, PID_UART1_RX, false ) Ģ) When testing between a DSPS device role and the Android phone application the tool does not recognize the default BDaddress. GPIO_ConfigurePin( GPIO_PORT_0, GPIO_PIN_5, INPUT_PULLUP, PID_UART1_RX, false ) // set UART Rx to input_PULL-UP This is solved by changing the configuration of the pin from INPUT to INPUT_PULLUP: The reason of the failure is that UART RX signal is in an undefined state.
MACROPLANT IBROWSE SOFTWARE
1) When running the DSPS keil application without a UART cable connected the software will run into the fault handler.